SI4711-B30-GM【PDF 26/40 页】IC TX FM RADIO 76-108MHZ 20UQFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录57

22页 23页 24页 25页 [26页]27页 28页 29页 30页

Si4710/11-B30

Rev. 1.1

After the rising edge of RST

, the pins, GPO1 and

GPO2/INT

, are used as general-purpose output (O) pins

as described in Section 5.12. GPO Outputs. In any

bus mode, commands may only be sent after V

and

supplies are applied.

5.11.1. 2-Wire Control Interface Mode

When selecting 2-wire mode, the user must ensure that

SCLK is high during the rising edge of RST

, and stays

high until after the first start condition. Also, a start

condition must not occur within 300 ns before the rising

edge of RST

2-wire bus mode uses only the SCLK and SDIO pins for

signaling. A transaction begins with the START

condition, which occurs when SDIO falls while SCLK is

high. Next, the user drives an 8-bit control word serially

on SDIO, which is captured by the device on rising

edges of SCLK. The control word consists of a seven bit

device address followed by a read/write bit (read = 1,

write = 0). The Si4710/11 acknowledges the control

word by driving SDIO low on the next falling edge of

SCLK.

Although the Si4710/11 responds to only a single device

address, this address can be changed with the SEN

(note that the SEN

pin is not used for signaling in 2-wire

mode). When SEN

= 0, the seven-bit device address is

0010001. When SEN

= 1, the address is 1100011.

For write operations, the user then sends an eight bit

data byte on SDIO, which is captured by the device on

rising edges of SCLK. The Si4710/11 acknowledges

each data byte by driving SDIO low for one cycle, on the

next falling edge of SCLK. The user may write up to

eight data bytes in a single two-wire transaction. The

first byte is a command, and the next seven bytes are

arguments.

For read operations, after the Si4710/11 has

acknowledged the control byte, it drives an eight-bit

data byte on SDIO, changing the state of SDIO on the

falling edge of SCLK. The user acknowledges each data

byte by driving SDIO low for one cycle, on the next

falling edge of SCLK. If a data byte is not

acknowledged, the transaction ends. The user may

read up to 16 data bytes in a single two-wire

transaction. These bytes contain the response data

from the Si4710/11.

A 2-wire transaction ends with the STOP condition,

which occurs when SDIO rises while SCLK is high.

For details on timing specifications and diagrams, refer

Table 5,

2-Wire

Control

Interface

Characteristics

1,2,3

, on page 7, Figure 2, 2-Wire

Control Interface Read and Write Timing Parameters,

on page 8, and Figure 3, 2-Wire Control Interface Read

and Write Timing Diagram, on page 8.

5.11.2. SPI Control Interface Mode

When selecting SPI mode, the user must ensure that a

rising edge of SCLK does not occur within 300 ns

before the rising edge of RST

SPI bus mode uses the SCLK, SDIO, and SEN

pins for

read/write operations. For reads, the user can choose to

receive data from the device on either SDIO or GPO1. A

transaction begins when the user drives SEN

low. The

user then pulses SCLK eight times while driving an 8-bit

control byte (MSB first) serially on SDIO. The device

captures the data on rising edges of SCLK. The control

byte must have one of these values:

0x48 = write eight command/argument bytes (user

drives write data on SDIO)

0x80 = read status byte (device drives read data on

SDIO)

0xA0 = read status byte (device drives read data on

GPO1)

0xC0 = read 16 response bytes (device drives read data

on SDIO)

0xE0 = read 16 response bytes (device drives read data

on GPO1)

When writing a command, after the control byte has

been written, the user must drive exactly eight data

bytes (a command byte and seven argument bytes) on

SDIO. The data will be captured by the device on the

rising edges of SCLK. After all eight data bytes have

been written, the user raises SEN

after the last falling

edge of SCLK to end the transaction.

In any bus mode, before sending a command or reading

a response, the user must first read the status byte to

ensure that the device is ready (CTS bit is high). In SPI

mode, this is done by sending control byte 0x80 or

0xA0, followed by reading a single byte on SDIO or

GPO1. The Si4710/11 changes the state of SDIO or

GPO1 after the falling edges of SCLK. Data should be

captured by the user on the rising edges of SCLK. After

the status byte has been read, the user raises SEN

after

the last falling edge of SCLK to end the transaction.

When reading a response, the user must read exactly

16 data bytes after sending the control byte. It is

recommended that the user keep SEN

low until all bytes

Table 15. Bus Mode Select on Rising Edge of

RST

Bus Mode

GPO1

GPO2/INT

2-Wire

SPI

1 (must drive)

3-Wire

0 (must drive)

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式